Fluke 27 II and 28 II digital multimeters
14 February, 2011 | Fluke Australia Pty Ltd
The Fluke 27 II and 28 II digital multimeters, suitable for operating in harsh conditions, are IP67 rated for water and dust resistance and offer an extended operating temperature range of -15 to +55°C.
Fluke SmartView software upgrades
14 February, 2011 | Fluke Australia Pty Ltd
SmartView software, for the Ti32 thermal imager, is a modular suite of tools for viewing, annotating, editing and analysing infrared images. It fully supports the company’s IR Fusion technology and upgrades are complimentary for the life of the product.
Fluke VoltAlert 2AC non-contact voltage tester
14 February, 2011 | Fluke Australia Pty Ltd
The 2AC has been added to the VoltAlert AC non-contact voltage tester range. It is easy to use and tests for energised circuits and defective grounds. The tip of the pocket-sized tester will glow red when within close proximity of an outlet, terminal strip or power cord where voltage is present.
Fluke 1555 and 1550C insulation testers
14 February, 2011 | Fluke Australia Pty Ltd
The 1555 and redesigned 1550C insulation resistance testers are designed for a wide range of diagnostic and predictive maintenance programs.
Fluke 421D laser distance meter
14 February, 2011 | Fluke Australia Pty Ltd
The 421D laser distance meter is a distance measurement device with features that include audible feedback for taking room angle and incremental measurements, a ±45° tilt sensor for taking indirect measurements in hard-to-reach areas and enhanced Pythagoras calculation for indirectly determining distance.
Hart Scientific 1594A/1595A Super-Thermometers
14 February, 2011 | Fluke Australia Pty Ltd
The 1594A/1595A Super-Thermometers from Hart Scientific can be used for calibration of SPRTs, PRTs and thermistors.
Fluke 1650B series installation tester
14 February, 2011 | Fluke Australia Pty Ltd
The 1650B series installation tester provides two measurements at once and a dual display. PEFC/PSC and loop impedance are measured and displayed in parallel, which is claimed to save more than 50% of test time compared to other loop testers.
Fluke Calibration Stik thermometer
14 February, 2011 | Fluke Australia Pty Ltd
The Stik thermometer from Fluke Calibration is a suitable substitute for precision mercury- or spirit-filled glass thermometers. The RTD probe and thermometer readout are combined into one unit and calibrated as a system.
AMP NetConnect AMP-Twist 6AS RJ45 jack
14 February, 2011 | Commscope
The AMP-Twist 6AS RJ45 jack offers 800 MHz performance and exceeds the Category 6A component performance specification of ISO/IEC 11801 amendment 2.
SATEC PM175 power quality analyser
01 February, 2011 | SATEC (Australia) Pty Ltd
SATEC’s PM175 power quality analyser monitors power quality compliance to the EN50160 standard, flicker to the IEC61000-4-15 standard and harmonics to the IEC61000-4-7 standard.
Exfo AXS-200-850 ethernet test set
20 January, 2011 | TechRentals
Available to rent, the Exfo AXS-200-850 ethernet test set provides comprehensive test functionalities for installs, turning up or maintenance of ethernet and IP services. Examples include the activation and maintenance of metro ethernet networks, deployment of active ethernet (point-to-point) access services, and traffic generation and monitoring for network performance testing.
Fluke ScopeMeter 190 series II 4-channel portable scope
20 January, 2011 | Fluke Australia Pty Ltd
The ScopeMeter 190 series II, the claimed first 4-channel portable scope safety rated to CAT III 1000 V/CAT IV 600 V, combines performance, ruggedness and portability.
CHK PM35 power quality analyser/logger
14 January, 2011 | TechRentals
Available to rent, the CHK PM35 power quality analyser/logger is a portable power logger and disturbance analyser, supporting harmonic analysis as well as flicker and imbalance monitoring.
CHK PM35 power quality analyser/logger
10 January, 2011 | TechRentals
Available to rent, the CHK PM35 power quality analyser/logger is a portable power logger and disturbance analyser, supporting harmonic analysis as well as flicker and imbalance monitoring.
Irwin Jack Evo handsaw
07 January, 2011 | Irwin Tools
The Jack Evo handsaw is suitable for applications including overhead fascia and rafters, removing bottom plates, roughing-in plaster, demolition work, cutting PVC piping, making extreme mitre cuts in custom installations and all types of standard, general-purpose sawing.
